1. dmesg 一下看開機是否已經載入 NTFS module, 若有得話便可直接 mount。詳見：
http://www.linux-ntfs.org/content/view/127/63/
以下節錄您所需要的部份:
引用: dmesg | grep NTFS
引用:
Mount
Mounting an NTFS Volume is covered in more detail in Section 4 of the Linux-NTFS FAQ (in the Wiki).
First you need to know which device your NTFS Volume is on and you need to create a directory as a mount point.
/sbin/fdisk -l
The output might look like:
Disk /dev/hda: 64 heads, 63 sectors, 4465 cylinders
Units = cylinders of 4032 * 512 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 2125 4283968+ 07 NTFS/HPFS
/dev/hda2 2126 19851 35735616 0f Win95 Ext'd (LBA)
/dev/hda5 * 2126 4209 4201312+ 83 Linux
/dev/hda6 4210 4465 516064+ 82 Linux swap
mkdir /mnt/windows
mount /dev/hda1 /mnt/windows -t ntfs -r -o umask=0222
ls -l /mnt/windows
...
-r-xr--r-- 1 root root 9719 Aug 24 1996 ansi.sys
-r-xr--r-- 1 root root 15252 Aug 24 1996 attrib.exe
-r-xr--r-- 1 root root 28096 Aug 24 1996 chkdsk.exe
-r-xr--r-- 1 root root 5175 Aug 24 1996 choice.com
...
2. 若需要加裝NTFS module 的話，可以到這邊找您需要的:
http://www.linux-ntfs.org/content/view/187/
使用方法在 1. 的同一篇裡，節錄如下：
引用:
Install
You must be root for the rest of the commands. The examples will continue as if you downloaded kernel-ntfs-2.4.18-14.i686.rpm.
Note: Newer NTFS RPMs have names like
kernel-module-ntfs-2.6.8-1.541-2.1.17-0.fc.1.2.i586.rpm
Next install the rpm:
rpm -ihv kernel-ntfs-2.4.18-14.i686.rpm
Preparing... ############################### [100%]
1:kernel-ntfs ############################### [100%]
There should be no errors, just some '#'-charakters.
Note: newer NTFS RPMs will also print a message telling you if install succeeded.
If something goes wrong see the Help Section.
This is the only command we actually needed, but we'll go on and test what we have done.
Next load the kernel module
/sbin/modprobe ntfs
There should be no output. If there are a lot of error messages see the Help Section.
The next command, dmesg prints the kernel logs. We search them for NTFS using grep.
dmesg | grep NTFS
NTFS driver v1.1.22 [Flags: R/O MODULE]
We can now check that the kernel really understands NTFS. The output may vary slightly, but you are looking for the entry ntfs.
cat /proc/filesystems
nodev rootfs
nodev bdev
nodev proc
nodev sockfs
nodev tmpfs
nodev shm
nodev pipefs
ext3
ext2
nodev ramfs
nodev devpts
ntfs
3. 覺得拉哩拉雜很煩嗎？ 請換用 SuSE 10 或 Ubuntu，直接就支援了...
P.S. 以上在下皆Try 過可行
[frankliu 在 2006-7-30 12:37 AM 作了最後編輯]
| 
